MANUAL – Deskloft – Electric Height Adjustable Table

Key Highlights

Pure mechanics, tidy build, steady feel.

Type: Fold-away crank with smooth gearing
Height range: 690–1130 mm
Load rating: 80 kg even spread
Width adjust: 800–1250 mm frame size
Finishes: White and Black
Warranty: see product page for frame and parts

Who This Fits Best

Pick DLM-STL2S2M0-CB1AD when power points are scarce or uptime must be certain. The crank gives precise control for small height tweaks and the frame stays calm while typing.

Home study with a single screen or a light arm
Schools and labs that prefer no electronics
Teams needing a reliable backup workstation during outages

Why It Feels Better In Daily Use

The drive is quiet by design. A geared crank converts small turns into steady lift, so you hit the right height without overshoot. The 1-beam reversal column keeps motion aligned, and 600 mm feet hold the stance on tile or wood. Edges are gentle on sleeves, and the fold-away handle stays out of the way when not in use. Cable routes sit near the back so lines do not snag as you adjust.

Planted feel at tall settings for crisp typing
Turn-to-lift motion that is controlled and quiet
Rear routing that keeps cords clear
Fold-away handle that protects knees
No power needed, so uptime stays constant

Size And Fit Guide

Dial posture first, then pick width.

Chair setup: Adjust until hips and knees feel free
Sit mark: Set wrists neutral, note the handle turns to reach that height
Stand mark: Elbows near a right angle; record the turns needed
Surface pick: 1200 × 600 mm suits one display and notes; go wider for a second screen
Room checks: Small wall gap for cables, drawer reach, doorway width for future moves

Keep in mind: Frame width adjusts 800–1250 mm, so tight corners and small studios both land clean layouts on your height adjustable desk.

Specs At A Glance

Frame: SPCC steel, rectangular tubes 75×45 mm
Legs: 2-stage, 1-beam reversal column
Drive: manual crank, lift rate 6.12 mm per round
Noise: very low during turn
Handle: fold-away, removable for storage
Top pairing: DeskLoft 1200×600×18 mm tops in White or Black, or any size within the width range
Power: none required
Safety: simple mechanical reset steps noted in the guide
Planning data: bracket 500 mm, feet 600 mm, N.W 16 kg, G.W 18 kg, carton 96 × 24 × 18.5 cm.

What You Get In The Box

DLM-STL2S2M0-CB1AD frame parts in protective cartons
Legs, feet, cross-beam, brackets, labeled fasteners
Crank handle, quick-start sheet, care notes
Cable tray or power hub only if included on your order

Installation Options

We install: In select cities a technician assembles the frame, levels feet, routes cables, and sets your sit and stand marks so day one feels right.

DIY: Allow 35–50 minutes with a hex key set and a Phillips screwdriver. Align brackets, pre-drill where needed, test both heights with the crank, then tie cables so slack stays relaxed during moves.

CTA: Book Installation • Download Guide

Care And Long-Run Tips

Wipe with a soft cloth and mild cleaner
Use coasters under hot cups
Recheck visible screws after the first week
Keep a small loop at the rear hub for cords
Stay inside the 80 kg rating with even spread

These small habits protect finish, feel, and lift action over time.

Compare With Similar Models

Choose by power and load.

DLM-STL2S2M0-CB1AD Manual: no power, 2-stage, precise crank control
D48 Dual-Motor: 2-stage, higher load and quick presets
D63 Dual-Motor 3-Stage: extra travel for short users and tall users sharing one base

Real Setups

Set a compact writing desk with a 24-inch screen and a laptop stand. Or kit a lab bench with a light arm and a tray for tools. In narrow rooms, pair DLM-STL2S2M0-CB1AD with 1200 × 600. Share a photo and your turn counts in a review so the next buyer dials their fit faster.

Delivery, Warranty, Returns

The delivery window depends on pin code. A tracking link is sent after dispatch. Warranty for frame parts follows the terms listed on the product page and your invoice. Returns are accepted under policy when the unit is clean and packaging is intact. Need help? Send clear photos or a short clip with your order ID and support will guide the next step.

FAQs

1) How many turns does it take to move between sit and stand.

It varies by your marks. As a guide, moving 100 mm needs roughly 16–17 full turns at 6.12 mm per round. Do a quick count on day one and note the numbers.

2) Can I remove the crank when not using it?

Yes. The handle folds away and can be detached. Store it in the drawer and reattach in seconds when you need an adjustment.

3) Will this frame work with a keyboard tray?

Usually yes. Keep fasteners clear of the column brackets and stay inside the top’s safe zones. Share an underside photo for screw length advice.

4) Is the manual drive hard to turn under load.

With weight spread evenly inside 80 kg, the gearing keeps effort reasonable. For very heavy rigs or frequent changes, consider a dual-motor frame.

5) How do I level the desk on an uneven floor?

Use the adjustable feet. Place a small level on the top, tweak each foot until bubble center, then test at your tall mark. Recheck after two days if the floor slopes.

A Deal to Seal

Want height control without power. Choose DLM-STL2S2M0-CB1AD, add a White or Black top, and pick install or DIY. Note your sit and stand marks, keep cables relaxed, and enjoy calm adjustments with a sturdy, mechanical feel every day.

]]>